Introduction
An electric geyser is a crucial home appliance that provides hot water for bathing, cleaning, and household chores. However, many homeowners neglect regular maintenance, which can lead to high electricity bills, inefficient heating, leaks, and costly repairs.
To ensure that your electric geyser functions efficiently and lasts 10-15 years, regular maintenance is essential. In this article, we will cover practical maintenance tips to keep your electric geyser in optimal condition.
1. Flush and Clean the Water Tank
Over time, sediment and mineral deposits accumulate inside the water tank, reducing heating efficiency and causing corrosion. If not cleaned, the heating element will have to work harder, increasing power consumption and shortening the geyser’s lifespan.
How to Clean the Water Tank:
- Turn off the geyser and unplug it from the power source.
- Drain the water completely using the drain valve.
- Flush the tank with clean water to remove sediments.
- If you live in a hard water area, install a water softener to prevent excessive scaling.
Frequency: Perform this cleaning every six months.
2. Check and Replace the Heating Element
The heating element is the core component responsible for warming the water. It can get coated with limescale, reducing efficiency and causing higher electricity bills.
Signs Your Heating Element Needs Replacement:
- Water takes longer to heat than usual.
- The geyser does not heat water at all.
- Strange noises like popping sounds come from the geyser.
Solution: If the element is covered in deposits, remove it and clean it using vinegar or descaling solutions. If it is damaged, replace it with a new one.
3. Inspect the Thermostat for Accuracy
The thermostat controls water temperature. If it’s faulty, it may overheat water, increasing electricity bills or preventing proper heating.
How to Maintain the Thermostat:
- Keep the temperature set to 50-60°C to prevent excessive heating.
- If water is too hot or too cold, test the thermostat and replace it if needed.
Check the thermostat every 3-6 months.
4. Test the Pressure Relief Valve (PRV)
The pressure relief valve prevents excessive pressure buildup inside the tank, which can lead to explosions or leaks.
How to Test the PRV:
- Lift the valve lever slightly to release some water.
- If water flows freely, the valve is working.
- If no water comes out or it continuously drips, replace it immediately.
Inspect the PRV every 6 months for safety.
5. Insulate the Tank and Pipes
Heat loss increases electricity consumption. To improve efficiency:
- Wrap the geyser tank with an insulation blanket.
- Cover exposed pipes with foam insulation sleeves to retain heat.
6. Check Electrical Wiring and Connections
Loose or damaged wiring can cause short circuits, overheating, or fire hazards.
What to Do:
- Inspect wiring connections for damage or burns.
- If you smell burning plastic, turn off the geyser and call an electrician.
Check wiring every 6 months.
7. Schedule Professional Maintenance
Even if you perform DIY maintenance, hire a professional once a year to:
- Check for hidden issues inside the geyser.
- Ensure the thermostat and heating element are working efficiently.
Conclusion
By following these maintenance tips, you can extend your electric geyser's lifespan, reduce power consumption, and prevent costly repairs. A well-maintained geyser ensures consistent hot water supply while operating safely and efficiently.
Introduction
Over time, electric geysers may develop problems due to wear and tear. Many of these issues can be prevented with proper maintenance. Below are the most common geyser problems and how to fix them.
1. Geyser Not Heating Water
This is one of the most common problems.
Causes:
- Burnt-out heating element
- Faulty thermostat
- Electrical connection issues
Solution:
- Check if the geyser is getting power.
- Test and replace the thermostat if it’s faulty.
- Inspect the heating element and replace it if needed.
2. Water Leaking from the Geyser
Causes:
- Loose pipe connections
- Faulty pressure relief valve
- Corroded tank
Solution:
- Tighten all pipe connections.
- If the PRV is leaking, replace it.
- If the tank is corroded, consider replacing the geyser.
3. Geyser Making Strange Noises
If you hear popping or rumbling sounds, it’s likely due to sediment buildup.
Solution:
- Flush the tank to remove deposits.
- Clean the heating element with vinegar.
4. Water Takes Too Long to Heat
Causes:
- Sediment buildup
- Low-wattage heating element
Solution:
- Flush the geyser tank.
- Upgrade to a higher wattage heating element.
5. Water Pressure Too Low
Causes:
- Blocked inlet valve
- Faulty PRV
Solution:
- Clean the inlet valve filter.
- Replace the PRV if necessary.
Conclusion
Troubleshooting these issues early can prevent costly repairs and extend your geyser’s lifespan.
Introduction
A well-maintained geyser uses less electricity, reducing energy bills. Follow these energy-saving tips to improve efficiency.
1. Set the Right Temperature
A thermostat setting of 50-60°C is optimal for efficiency and safety.
2. Turn Off the Geyser When Not in Use
Keeping the geyser on all day wastes energy. Install a geyser timer switch to automate its operation.
3. Insulate the Geyser and Pipes
Using insulation blankets and foam pipe covers helps retain heat, reducing power consumption.
4. Use a Low-Flow Showerhead
A low-flow showerhead reduces hot water usage, saving electricity.
5. Flush the Tank Regularly
Sediment buildup forces the geyser to work harder, increasing energy use. Flush the tank every six months.
6. Replace Old Geysers with Energy-Efficient Models
Older geysers consume more electricity. Upgrade to a 5-star rated geyser for better efficiency.
7. Schedule Annual Professional Servicing
A technician can fine-tune your geyser for maximum efficiency.
Conclusion
By following these energy-saving maintenance tips, you can reduce electricity consumption, save money, and extend your geyser’s lifespan.
Final Thoughts
These three articles cover essential maintenance tips, troubleshooting solutions, and energy-efficient practices to help you keep your electric geyser running smoothly. If you need any modifications or additional details, let me know!
